Number P0102: Mass or Volume Air Flow Sensor A Circuit Low
The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a voltage or, on GM, Saab and newer Ford systems,
Can you drive with P0102?
Severity: Fix promptly — drivability fault. Short trips at moderate speed only. If the car has entered limp mode (won't rev, stuck in one gear), have it towed rather than forcing it.
If you ignore it: Limp-mode faults tend to strand you, and several of them (misfires, throttle faults) damage other parts while you wait.
This is the #13 most common code in our top-150 library, in the fuel trim & air metering family (Powertrain system). Severity is Number Nest's editorial triage — if the light is flashing or the car feels unsafe, stop driving it whatever any page says.
What P0102 means
The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a voltage or, on GM, Saab and newer Ford systems, a frequency. P0102 means the signal is below its electrical lower limit – a frequency that is too low or a voltage that is too low. Documented limits: GM petrol 450 Hz or less, GM diesel below 276 Hz, Ford digital below 1.5 kHz for 5 s, Ford analogue below 0.244 V. 'Low' describes the signal: typically an open or grounded signal wire, missing supply voltage or failed electronics. Saab notes that a large leak between sensor and throttle can also cause it. GM and Saab need two trips; the engine runs on a calculated substitute value.
Systems involved: mass air flow sensor, mass air flow sensor wiring, sensor supply voltage.
Causes, ranked by likelihood
| # | Cause | Likelihood |
|---|---|---|
| 1 | Signal wire open or shorted to ground, connector corroded or loose | most likely |
| 2 | Sensor electronics failed | most likely |
| 3 | Missing supply voltage (fuse, relay) or poor ground | possible |
| 4 | Large leak or disconnected duct between sensor and throttle | less common |
Check them in order — the list is ranked so the likely, cheaper causes come before the expensive part.
Symptoms you may notice
- Check engine light on
- Lack of power, hesitation, substitute value mode
- Rough idle or stalling
- Higher fuel consumption
Misdiagnosis traps
- A MAF code on a car with a dead battery history: low voltage during cranking can set circuit codes that never return after a charge and clear.
- A completely dead MAF reading (0 g/s with the engine running) is usually power, ground or the connector — the sensing element rarely fails to exactly zero.
How a good shop confirms it
- Check MAF power and ground at the connector, then the signal while running.
Repair options & costs
| Repair | Shop total (parts + labor) | DIY (parts only) | Difficulty |
|---|---|---|---|
| Mass air flow (MAF) sensor | $158 – $420 | $120 – $320 (parts only) | 1/5 |
National ranges from Number Nest's cost model (midsize car, independent shop, US-average labor). Published cross-check — Mass air flow (MAF) sensor: CarMD 2026 national average $346.
OBDex repair data for this code rates the job difficulty easy with a typical labor time in the 0.3–1.5 hour range and DIY possible: yes.
Price this repair in your state
Estimated total: — (midsize car, independent shop)
Frequently asked questions
P0101 vs P0102 — what changed?
P0101 says the reading is implausible (performance); P0102 says the signal is electrically low or absent (circuit). P0102 starts with wiring checks.
How much does it cost to fix P0102?
The fix most associated with this code — mass air flow (maf) sensor — runs $158 – $420 at an independent shop for a midsize car in our cost model (parts + labor, US average). The code names a system, not a part, so confirm the cause before spending: the ranked causes above are ordered by likelihood.
Can I drive with P0102?
See the can-you-drive verdict above — it is based on the system involved and the cascading-damage risk, and it is our editorial triage, not a manufacturer instruction. If the light is flashing or the car feels unsafe, stop driving it regardless of any code.
Will P0102 clear itself?
If the fault was a one-off (a loose cap, a cold-start glitch), the light can go out after several clean trips and the code ages into history. A fault that is still present re-sets the code as soon as the car runs that self-test again — monitors run under specific conditions, which is why "it hasn't come back in two days" is not proof of a fix.
Will my car fail inspection with P0102?
In states with OBD-based emissions inspection, yes — an illuminated check-engine light or an incomplete readiness monitor fails the test regardless of what the tailpipe would show. C-codes (ABS) fall under safety inspection instead in states that have one.
What should I check first for P0102?
The first item on the ranked-causes list above — it is ranked likelihood-first for exactly this reason — plus the free checks: recent work in the area (connectors left loose are a classic), fluid levels, and the battery and grounds on electrical codes.
Where this data comes from
Code facts, causes and symptoms come from OBDex — an open dataset of independently authored descriptions of the standardized generic OBD-II codes (CC0 1.0, public domain; github.com/foerbsnavi/OBDex). The SAE J2012 document itself is copyrighted and is not reproduced here. Cost ranges are Number Nest's own US planning model: national parts and labor ranges cross-checked against the CarMD Vehicle Health Index 2026 published averages, with labor adjustable by the BLS OEWS May 2025 state wage index for auto technicians (occupation 49-3023) — a wage index, not a surveyed shop rate. Severity and can-you-drive notes are our editorial triage, not a manufacturer instruction.