Number P0760: Shift Solenoid C
A shift solenoid is an electrically switched valve in the valve body. Manufacturers use these codes differently: Ford reports an open circuit with the base code and shorts separately, and the letter is not tied to a valve number (Saab's Aisin 9-5: C = valve S4, D = valve S5). P0760 is the general co
Can you drive with P0760?
Severity: Fix promptly — drivability fault. Short trips at moderate speed only. If the car has entered limp mode (won't rev, stuck in one gear), have it towed rather than forcing it.
If you ignore it: Limp-mode faults tend to strand you, and several of them (misfires, throttle faults) damage other parts while you wait.
This is the #133 most common code in our top-150 library, in the transmission family (Powertrain system). Severity is Number Nest's editorial triage — if the light is flashing or the car feels unsafe, stop driving it whatever any page says.
What P0760 means
A shift solenoid is an electrically switched valve in the valve body. Manufacturers use these codes differently: Ford reports an open circuit with the base code and shorts separately, and the letter is not tied to a valve number (Saab's Aisin 9-5: C = valve S4, D = valve S5). P0760 is the general code for solenoid C and, at Ford, means an open circuit: the smart driver feedback disagrees with the command for 0.5–5 s, continuously; shorts to ground and power are P0979/P0980. On Ford's 6R80, 6F35/6F55 and 6R140, solenoid C is the proportional valve of the CB26 brake for second and sixth gear. If the solenoid supply is switched off, Ford transmissions keep park, reverse, neutral and fifth gear with maximum pressure.
Systems involved: shift solenoid, transmission valve body, transmission wiring, transmission control module.
Causes, ranked by likelihood
| # | Cause | Likelihood |
|---|---|---|
| 1 | Open or corroded wire, connector or internal harness | most likely |
| 2 | Solenoid coil open or shorted | possible |
| 3 | Solenoid supply (high-side switch) missing | less common |
| 4 | Module driver faulty | less common |
Check them in order — the list is ranked so the likely, cheaper causes come before the expensive part.
Symptoms you may notice
- Check engine or transmission warning lamp
- Limp mode in a fixed gear (Ford: fifth with maximum pressure)
- Second and sixth gear missing (Ford CB26)
Misdiagnosis traps
- Replacing the part named by the code title without testing. The code reports a failed self-test; the cause list above is ranked so the likely, cheap causes are checked before the expensive part is condemned.
- Clearing the code and declaring victory when the light stays off for a day — the monitor that sets this code runs only under specific driving conditions.
(General diagnostic guidance for this code family — no code-specific trap is published for this code.)
How a good shop confirms it
- Confirm the code and record any companion codes — companions narrow the system fast.
- Inspect the affected components and their wiring/connectors for damage, corrosion and looseness.
- Test the top-ranked cause with live data or a multimeter before replacing anything.
(Standard diagnostic path for this family, labeled as general guidance.)
Repair options & costs
| Repair | Shop total (parts + labor) | DIY (parts only) | Difficulty |
|---|---|---|---|
| Transmission shift solenoid | $338 – $838 | $150 – $400 (parts only) | 4/5 |
National ranges from Number Nest's cost model (midsize car, independent shop, US-average labor).
OBDex repair data for this code rates the job difficulty medium with a typical labor time in the 0.5–4 hour range and DIY possible: see the guide above.
Price this repair in your state
Estimated total: — (midsize car, independent shop)
Frequently asked questions
How much does it cost to fix P0760?
The fix most associated with this code — transmission shift solenoid — runs $338 – $838 at an independent shop for a midsize car in our cost model (parts + labor, US average). The code names a system, not a part, so confirm the cause before spending: the ranked causes above are ordered by likelihood.
Can I drive with P0760?
See the can-you-drive verdict above — it is based on the system involved and the cascading-damage risk, and it is our editorial triage, not a manufacturer instruction. If the light is flashing or the car feels unsafe, stop driving it regardless of any code.
Will P0760 clear itself?
If the fault was a one-off (a loose cap, a cold-start glitch), the light can go out after several clean trips and the code ages into history. A fault that is still present re-sets the code as soon as the car runs that self-test again — monitors run under specific conditions, which is why "it hasn't come back in two days" is not proof of a fix.
Will my car fail inspection with P0760?
In states with OBD-based emissions inspection, yes — an illuminated check-engine light or an incomplete readiness monitor fails the test regardless of what the tailpipe would show. C-codes (ABS) fall under safety inspection instead in states that have one.
What should I check first for P0760?
The first item on the ranked-causes list above — it is ranked likelihood-first for exactly this reason — plus the free checks: recent work in the area (connectors left loose are a classic), fluid levels, and the battery and grounds on electrical codes.
Where this data comes from
Code facts, causes and symptoms come from OBDex — an open dataset of independently authored descriptions of the standardized generic OBD-II codes (CC0 1.0, public domain; github.com/foerbsnavi/OBDex). The SAE J2012 document itself is copyrighted and is not reproduced here. Cost ranges are Number Nest's own US planning model: national parts and labor ranges cross-checked against the CarMD Vehicle Health Index 2026 published averages, with labor adjustable by the BLS OEWS May 2025 state wage index for auto technicians (occupation 49-3023) — a wage index, not a surveyed shop rate. Severity and can-you-drive notes are our editorial triage, not a manufacturer instruction.